onceownedby 
Nowadays, there are so many products of pentair carbon water filter c1 in the market and you are wondering to choose a best one. You have searched for pentair carbon water filter c1 in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings pentair carbon water filter c1 which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
Pentek C1-20 Carbon-Impregnated Cellulose Filter Cartridge, 20" x 2-1/2", 5 Micron
- Reduces fine sediment and chlorine taste and odor in residential drinking water
- Nominal filtration rating of 5 microns
- Carbon-impregnated cellulose media with a polyester backing and external polyethylene netting for strength
- Initial pressure drop of 1 psi at a flow rate of 5 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
This Pentek C1-20 carbon-impregnated cellulose filter cartridge reduces fine sediment and chlorine taste and odor in residential drinking water. It has a nominal filtration rating of 5 microns at an efficiency of 85%. The filter will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 75% in up to 5,000 gallons at a flow rate of 2 gallons per minute (gpm). The cartridge is made of cellulose media that has been impregnated with powdered activated carbon (PAC), with a polyester backing and external polyethylene netting for strength. It has an initial pressure drop of 1 pound per square inch (psi) at a flow rate of 5 gallons per minute (gpm), and operates over a temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C). This filter cartridge is for use in residential drinking water purification.
Specifications
| Nominal filtration rating | 5 microns |
| Initial pressure drop at 5 gpm | 1 psi |
| Chlorine reduction capacity | 5,000 gallons at 2 gpm |
| Operating temperature range | 40 to 125 degrees F (4.4 to 51.7 degrees C) |
| Maximum dimensions (H x W) | 20 x 2-1/2 inches (508 x 64 mm) |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 75%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek C1 Carbon Filter Cartridge, 9-3/4" x 2-1/2", 5 Micron
- Reduces fine sediment and chlorine taste and odor in residential drinking water
- Nominal filtration rating of 5 microns
- Carbon-impregnated cellulose media with polyester backing and netting for strength and dirt-holding capacity
- Initial pressure drop of 4 psi at a flow rate of 5 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
This Pentek C1 carbon filter cartridge reduces fine sediment and chlorine taste and odor in residential drinking water. It has a nominal (85%) filtration rating of 5 microns, and will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 75% in up to 2500 gallons at a recommended flow rate of 1 gallon per minute (gpm). This cartridge is made of cellulose media impregnated with powdered activated carbon (PAC), reinforced by polyester backing and netting for strength and dirt-holding capacity. The nitrile butadiene rubber (Buna-N) gasket seals the cartridge against the housing (sold separately). The cartridge has an initial pressure drop of 4 pounds per square inch (psi) at a flow rate of 5 gpm, and it operates over a temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C). This filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is for use in various applications, including drinking water purification, laboratory water treatment, and film processing, among others .
Specifications
| Nominal filtration rating | 5 microns |
| Chlorine reduction capacity | 2500 gallons at 1 gpm |
| Initial pressure drop at 5 gpm | 4 psi |
| Operating temperature range | 40 to 125 degrees F (4.4 to 51.7 degrees C) |
| Maximum dimensions (H x W) | 9-3/4 x 2-1/2 inches (248 x 64 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 75%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
(Package Of 3) Pentek C-1 Carbon Water Filters (9.75" x 2.5")
Pentek C-1 Water Filter Replacement Information: Easy to install in whole house water filter systems, reverse osmosis systems, or recreational vehicle systems Pentek C-1 Water Filter Equivalent Brands: The following Culligan water filter models hold this sediment water filter cartridge: HF-150, HF-160, HF-360, HF-365 The following Ametek, USFilter, and Plymouth Products models hold this sediment water filter cartridge: #10 Blue, #10 Clear The Pentek C1 water filter also fits Cuno, AquaPure, Omni, Sears, Fulflo, Teledyne Water Pik, Ace, Master Plumber, Flotec, Honeywell, General Electric, American Plumber, and most other water filter housings for 10" x 2.5" filters The Pentek C-1 is the same as the Ametek C1, Culligan C-1, USFilter C-1, Pentek C-1, American Plumber C-1, Plymouth Products C-1, or Kleen Plus C1. Ametek # 155002 is the same as the Pentek C1 water filter. .Pentek C1 Carbon Water Filter Cartridge Specs: Dimensions:9.75" x 2.5" (248 mm x 64mm) Micron Rating (Nominal):5 Micron Temperature Rating: 40?F to 125?F (4.4? C to 51.7?C) Initial ∆P (psi) @ Flow Rate (gpm): 4 psi @ 5 gpm (0.3 bar 19 L/min) Chlorine Taste & Odor Reduction @ Flow Rate (gpm): >2,500 gallons @ 1 gpm (>9,500 liters @ 3.8 L/min)NOTE: Estimated capacity tested at given flow rate using 2 ppm free available chlorine to 0.5 ppm breakthrough. Pentek C1 Carbon Filter Materials of Construction: Filter Media:PAC Impregnated Cellulose End Caps:Vinyl Plastisol Netting:Polyethylene Core:Polypropylene Reinforcement Backing:Cellulose Polyester (Package Of 3)
Pentek C1 Carbon Filter Cartridge, 9-3/4 x 2-1/2, 5 Micron (4, 1 Pack)
- Qty. 4 of Pentek 155002-43
- General purpose taste & odor reduction for residential chlorinated water supplies
- High flow rates possible due to low initial pressure drop
- Good dirt-holding capacity
- Constructed of a carbon-impregnated cellulose media, these dual-purpose cartridges filter out fine sediment particles and reduce unwanted taste, odor, and chlorine taste & odor from your tap water. A polyester reinforcement backing and external netting provide additional strength and dirt-loading capacity.
Pentair’s Pentek C Series carbon filter cartridges offer an economical solution for all your general purpose water filtration needs. Constructed of a carbon-impregnated cellulose media, these dual-purpose cartridges filter out fine sediment particles and reduce unwanted taste, odor, and chlorine taste & odor from your tap water. A polyester reinforcement backing and external netting provide additional strength and dirt-loading capacity. Recommended for chlorinated water supplies.
Pentek EP-20BB Carbon Block Filter Cartridge, 20" x 4-5/8", 5 Microns
- Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water
- Nominal filtration rating of 5 microns
- Bonded PAC media with polyolefin pre-filter and polyethylene netting for extended life
- Initial pressure drop of 5.5 psi at a flow rate of 5 gpm
- Temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C)
This Pentek EP-20BB carbon block filter cartridge reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. It has a nominal (85%) filtration rating of 5 microns. The filter will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 90% in up to 40,000 gallons at a flow rate of 4 gallons per minute (gpm). This cartridge is made of bonded powdered activated carbon (PAC) filter media wrapped in a polyolefin pre-filter with polyethylene outer netting. The nitrile butadiene rubber (Buna-N) gaskets seal the cartridge against the housing (sold separately). The cartridge has an initial pressure drop of 5.5 pounds per square inch (psi) at a flow rate of 5 gallons per minute (gpm), and operates over a temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C). This carbon block filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for purification of residential and commercial drinking water.
Specifications
| Nominal filtration rating | 5 microns |
| Initial pressure drop at 5 gpm | 5.5 psi |
| Chlorine reduction capacity | 40,000 gallons at 4 gpm |
| Temperature range | 40 to 180 degrees F (4.4 to 82.2 degrees C) |
| Maximum dimensions (H x W) | 20 x 4-5/8 inches (508 x 118 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 90%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Pentek RFC20-BB Carbon Filter Cartridge, 20" x 4-1/2"
- Reduces chlorine taste and odor in drinking water
- Granular activated carbon (GAC) media with spun polypropylene core and polypropylene end caps for strength
- Porous polyethylene 70-micron outer shell reduces carbon fines and other particles
- Initial pressure drop of 0.90 psi at a flow rate of 4 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
Pentek GAC-BB Drinking Water Filter (9-3/4" x 4-1/2")
Pentek EPM-10 Carbon Block Filter Cartridge, 9-3/4" x 2-7/8", 10 Microns
- Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water
- Nominal filtration rating of 10 microns
- Bonded PAC media with polyolefin pre-filter and polyethylene netting for extended life
- Initial pressure drop of 1.5 psi at a flow rate of 1 gpm
- Temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C)
This Pentek EPM-10 carbon block filter cartridge reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. It has a nominal (85%) filtration rating of 10 microns. The filter will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 90% in up to 3,000 gallons at a flow rate of 1 gallon per minute (gpm). This cartridge is made of bonded powdered activated carbon (PAC) filter media wrapped in polyolefin with polyethylene outer netting. The nitrile butadiene rubber (Buna-N) gaskets seal the cartridge against the housing (sold separately). The cartridge has an initial pressure drop of 1.5 pounds per square inch (psi) at a flow rate of 1 gallon per minute (gpm), and operates over a temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C). This carbon block filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for purification of residential and commercial drinking water.
Specifications
| Nominal filtration rating | 10 microns |
| Initial pressure drop at 1 gpm | 1.5 psi |
| Chlorine reduction capacity | 3,000 gallons at 1 gpm |
| Temperature range | 40 to 180 degrees F (4.4 to 82.2 degrees C) |
| Maximum dimensions (H x W) | 9-3/4 x 2-7/8 inches (248 x 73 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 90%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Everpure H-104 Water Filter Replacement Cartridge (EV9612-11)
- Reduces the following contaminants: lead, cysts such as giardia lambila, and cryptosporidium
- Removes chlorine taste and odor, dirt and cloudiness, mold and algae and particles 1/2-Micron and larger in size
- Finely polishes treated water to premium quality for drinking and cooking
- a lower operating cost that is below the price of bottled water
- Everpure systems are easily installed using common household tools and cartridge replacement is easy
- Inhibits limescale build-up in water-using appliances
Aquverse A100 2-Pack Replacement Filters
Aquverse replacement filters, Part Number: A100, Made in United States, Brand Name: Aquers, reduces Lead.
Conclusion
By our suggestions above, we hope that you can found pentair carbon water filter c1 for you.Please don’t forget to share your experience by comment in this post. Thank you!
